|
GENERAL
|
PE07 can used be an anti-corrosive coating or additional layer for anticorrosive coating. which will enhance sealing and anti-corrosion properties. It’s possessed of higher sealing property. In addition, it forms a coating with good resistance to heat and corrosion , this paint is able to match with most pain
|
|
總述
|
PE07 可用做防銹底漆，也可作為防銹漆的加涂層。增加封閉性和防腐蝕性能。具有較高的封閉性，耐熱性和防腐性良好。與大多數涂料配套。
|
|
RECOMMENDED USES
|
steel structure
|
|
推薦用途
|
適用于各種鋼結構
|
|
SPECIFICATION DATA
|
|
|
技 術 參 數
|
|
|
Vehicle Type/Pigment Type
|
Modified epoxy
|
|
漆料類型/顏料類型
|
改性環氧
|
|
Colors .
|
grey
|
|
顏色
|
灰
|
|
Mixing ratio
|
By weight: 10(base) to 1(curing agent);
|
|
混合比率
|
重量比10(基料)：1(固化劑)
|
|
Curing agent
|
PE07C01
|
|
固化劑
|
PE07C01
|
|
Specific gravity(mixture)
|
1.42±0.05Kg/dm3 (23℃/73.4℉)
|
|
比
|
重 1.42±0.05公斤/立方分米
|
|
Volume of Solids
|
65% （Theoretical）
|
|
體積固體份
|
65%(理論上)
|
|
Flash point(Abel)
|
Base:>23℃;Curing agent:>40℃
|
|
閃點
|
基底>23℃；固化劑：>40℃
|
|
Theoretical covering capability
|
6.5 Sq.m/Lt. at 100 microns (4mils)
|
|
理論覆蓋能力
|
6.5平方米/ 升
|
|
Typical film thickness per coat
|
Wet:154 microns (6 mils) ; Dry:100 microns (4mils)
|
|
單層膜厚
|
濕膜：154um；干膜：100um
|
|
Application
|
method Brush, Roller or Airless Spray
|
|
施工方法
|
手刷、滾輪刷、無氣噴涂
|
|
Thinner
|
Product: TH03- Cleaning: TH03
|
|
稀釋劑
|
產品：TH03； 清潔劑：TH03
|
|
V.O.C
|
285 grams/Lt.
|
|
揮發性有機化合物
|
285克/升.
|
|
Pot Life
|
(at 23℃/73.4℉) 8h at 23℃(73.4℉)
|
|
混合使用期
|
23℃(73.4℉)時8h
|
|
Drying time
|
Surface dry: 2 hours at 23℃(73.4℉)
|
|
干燥時間
|
表干：23℃(73.4℉)時2小時
|
|
Overcoating time
|
Min:10 hours at 23℃(73.4℉); Max:7 days. If maximum overcoat
|
|
重涂時間
|
最短：23℃(73.4℉)時10小時；最長：7天。
|
|
Ambient temperature
|
Min : 5℃(41℉) ;Max:40℃(104℉)
|
|
環境溫度
|
最低：5°C；最高40°C
|
|
Substrate temperature
|
Min : 5℃(41℉) ;Max:40℃(104℉)
|
|
底材溫度
|
最低：5°C；最高40°C
|
|
Packing
|
Product is a two pack component, available in 1,5 and 20 Kg combined packs.
|
|
包裝
|
雙組份 ,包裝規格有1，5，20公斤包裝
|
|
Storage conditions
|
The product must be stored in accordance with national regulations. The product should be kept in a cool well ventilated places protected f rom high temperatures. Containers MUST BE kept tightly closed. Shelf life: 1 year.
|
|
儲存及有效期
|
產品儲存必須和國際準則一致。產品應在良好的 通風處保存，防止高溫。容器必須保持緊緊關嚴。 有效期：1年。
|
|
APPLICATION GUIDE
|
|
|
施 工 指 導
|
|
|
SURFACE
|
PE07, is designed for application directly to iron/ steel surfaces pre-treated by Blast cleaning to Sa2.5 of the Swedish SIS 0055900. All surfaces must be free of oil, grease, moisture another foreign matter prior to blasting.
|
|
表面處理
|
PE07 設計用于在鋼鐵表面經噴砂預處理達到 瑞典標準SIS055900的Sa2.5級后直接涂裝。 所有表面必須無油脂、水分或其它雜質，然后才能噴砂。
|
|
MIXING AND THINNING
|
PE07 is a two pack product, both packs containing the proper ratio of ingredients. The entire contents of each container must be mixed together, as supplied. Stir base first to obtain smooth homogenous condition not longer than 3 minutes. Use the total content of each pack. The use of a speed adjustable power mixer is recommended. However, if necessary due to equipment limitation, thinning is allowed with TH03 (max. 3% v/v)
|
|
混合和稀釋
|
PE07是雙組份產品，各種成分在使用中有 明確的配比;使用時各種成份必須一起混合.首先攪拌 基料達到光滑均勻，但時間不得超過2分鐘，基料達 到均勻狀態后緩慢地加入固化劑，須連續攪拌三分鐘. 使用每罐全部涂料的可使用速度可調的電動攪拌機， 過度攪拌會加速固化，降低產品的壽命。不建議進行 稀釋.但是,如果由于設備局限性,可以用TH03進行稀釋.
|
|
APPLICATION.
|
PE07,can be applied by airless spray. DO NOT APPLY OVER WET SUPFACES OR UNDER HUMID CONDITIONS,Ventilation It is very important for the safety of the applicator and the proper performance of EURO-PE07 that good ventilation be provided to all portions of the enclosed area . Dry air IS a must since EURO-PE07, must Not be applied with humidity over 85%
|
|
涂裝
|
PE07， 可以采用無氣噴涂。 不要在濕表面或潮濕條件下施工 通風對于施工人員的安全，密閉區域的各部分有 良好有通風是很重要的�？諝獗仨毷歉稍锏�， 不能在濕度超過85%條件下施工。
|
|
SAFETY
|
WARNIGN: Cause eye and skin irritation. Reaction vapour may cause respiratory irritation in sensitive individuals. May cause allergic skin reaction. Avoid breathing vapours. Do not get in eyes on skin or clothing, ear eye and skin protective equipment. Use appropriate respirator, it is recommended to avoid potential respiratory, preferably mouth-to-mouth, and call physician. BURNS: Exothermic reaction causes product to heat which is normal. Be careful handling after mixing product. Use gloves. FIRST AID: In case of eye contact immediately flush with plenty of water for at least 15 minutes while removing contaminated clothing and shoes. Wash skin contact area with soap.
|
|
安全措施
|
警告:會引起眼睛和皮膚的刺激.反應的蒸汽可能會引起 過敏人群的呼吸道刺激.可能會引起皮膚過敏反應.避免 呼吸蒸汽.請勿觸及眼睛、皮膚。要使用眼、耳、 皮膚的防護用具，使用合適的面具，以避免潛在的 呼吸道刺激。使用后用清水徹底的清洗皮膚。如有 不適請咨詢醫生。衣物再次使用前要洗滌。如果沒有 呼吸要進行人工呼吸，最好嘴對嘴，并請醫生處理。 灼傷：放熱反應會使產品變熱，超出正常水平。 在混合后要小心處理。使用手套。 急救：如果不慎接觸了眼睛，立即用清水沖洗 至少15分鐘，并脫去污染的衣鞋， 用肥皂清洗接觸后的皮膚。
|
|
DISCLAMER
|
This is not a specification and all information is given in good faith. Every values presented as Theoretical were calculated from the product formula If requested, can inform any internal measurement method used to determinate any given value presented. Since conditions of use are beyond the manufacturers control information contained herein is without warranty, implied or otherwise, and final determination of the suitability of any information or material for the use contemplated is the sole responsibility of user. The product is intended for professional use only. In case of any doubt, contact your local agent.
|
|
提請注意
|
此文件不是正式的技術文件，所列出的信息是可靠的。 提供的的每個數值都是作為理論數據從產品的配方中 計算出來的。如果需要，可以告知任何上述 給出數據的內部常用測量確定方法。由于使用條件非 生產商所能控制，這里的信息不做為擔保。產品只是 用于專業使用。如有任何問題，請與當地代理商聯系。 向生產廠咨詢詳細的施工建議。
|
